Material-led machine selection
Laminating Machines for Paper and Board
Compare thermal, water-based, sheet-fed, corrugated-board and roll-to-roll systems by material, working width and automation level.
Category concept visual · final configuration follows the approved drawing and quotation
Start with the material you run.
Six machine families, grouped by the material and bonding method they are built for.
Corrugated Board Laminators
View productsWater-Based Adhesive Laminators
View products
Thermal Laminators
View products
Roll-to-Roll Laminators
View products
Coating & Glazing Machines
View productsMatch the process to the material.
Every application below pairs a real selection question with the machine built to answer it.
Printed sheetsHeated rollerFinished surface
Application 01
Paper sheets and thermal lamination
Pre-cut sheets and covers pass through heated rollers where thermal film bonds to the surface, producing a durable gloss or matte finish for menus, folders and covers.
Compare this machine familyBoard + sheetAdhesive / filmBonded board
Application 02
Corrugated board and water-based glue or film
Flute board and packaging blanks can follow an adhesive or film route. The substrate, finished-product requirements and approved consumables determine the final configuration.
Compare this machine familyUnwindLaminationRewind
Application 03
Roll-to-roll materials and continuous processing
Reel-fed printed or coated material runs continuously through the lamination zone, suited to high-volume output without the stop-start cycle of sheet feeding.
Compare this machine familyUnderstand the material path.
A configuration-level process diagram—clearly separated from real factory or machine-trial evidence.
FeedSheet stack or reel
BondThermal film or approved adhesive route
DeliverStack, cut or rewind
01
Feeding
Sheets or reel material enter the machine aligned to the working width, guided by feed rollers before the bonding stage.
02
Lamination / coating zone
Heated rollers or a glue application unit bond film or adhesive to the substrate under controlled pressure.
03
Output / sample
Finished sheets or rolled material exit the machine ready for cutting, stacking or further converting.
From material to machine proposal.
Three inputs move you from inquiry to a matched configuration.
1.0
Send the material
- Substrate & thickness
- Maximum width
- Film / glue route
2.0
Confirm the configuration
- Target output
- Automation level
- Local voltage
3.0
Receive the proposal
- Matched machine family
- Configuration summary
- Confirmed specification sheet
Compare the decisions that change the machine.
Confirmed values replace "To confirm" once your material and configuration are set.
| Decision | Sheet-fed thermal | Corrugated board | Roll-to-roll |
|---|---|---|---|
| Material form | Sheet | Sheet / board | Reel |
| Lamination method | Thermal film | Water-based glue / film | Thermal or adhesive |
| Automation level | To confirm | To confirm | To confirm |
| Working width | To confirm | To confirm | To confirm |
| Feeding method | Sheet feeder | Sheet feeder | Unwind stand |
| Heating / glue system | Heated roller | Glue unit or heated roller | To confirm |
| Output handling | Stack delivery | Stack delivery | Rewind |
| Voltage & language | To confirm | To confirm | To confirm |
Questions before you send specs.
Answers separate confirmed standard capability from project-specific options.
The correct route depends on the substrate, required finish, film or adhesive specification, and downstream process. Send the material details and the route can be reviewed before configuration.
Sheet-fed suits pre-cut board and packaging blanks. Roll-to-roll suits continuous printed or coated material run from a reel. Tell us your incoming material format and we confirm the right feed path.
Working width is set by your largest sheet or roll dimension plus a practical margin. Send your maximum material size and we confirm the width that avoids trimming waste.
Sample runs on your own material are project-specific — confirm feasibility and lead time after sending your material specification.
Voltage and control-panel language options vary by machine family and are confirmed during configuration, not fixed in advance.
Installation support and operator training scope depend on the machine family and destination — this is confirmed as part of the proposal, not a fixed standard package.
Send the material. We'll narrow the machine.
Complete the selection inputs, then copy a structured inquiry summary. Direct transmission will be enabled once the verified sales channel is connected.